![rotary motor drag racing rotary motor drag racing](https://c8.alamy.com/comp/CE5YFH/highly-modified-and-turbocharged-mazda-rotary-wankel-20b-triple-rotor-CE5YFH.jpg)
- Rotary motor drag racing install#
- Rotary motor drag racing skin#
- Rotary motor drag racing full#
- Rotary motor drag racing mods#
- Rotary motor drag racing code#
This setup also requires special CNC machining to accept custom made outer gas sealing rings and also requires special balancing.
Rotary motor drag racing mods#
PBR III has all the mods of build I & II plus it uses lower compression 13b RX7 FD rotors.This setup requires special CNC machining of apex grooves and special corner seals.
![rotary motor drag racing rotary motor drag racing](https://cdn.shopify.com/s/files/1/0045/5124/5898/products/pettit-built-engine-800_800x.jpg)
So far there have been no failures to inspect. In theory this should double apex seal life. With these apex seals, the load carrying surface area (main wear area) is increased more than 50% and thus reduces surface loads more than 50% as well.
Rotary motor drag racing full#
Rotary motor drag racing skin#
Rotary motor drag racing install#
$245 We also at no charge clean, flow & PSI test the injectors, to insure proper fueling of our engines as well as easing the install for the techs insuring no problems with stuck valves or flaky injectors. We blend and smooth the factory machining at the base of the VDI valve plenum area reducing turbulence and improving flow as well as service and index the SSV, VDI & aux port valves, then install the manifold on the engine and test the valves for proper operation.
![rotary motor drag racing rotary motor drag racing](https://i.ytimg.com/vi/KK2fzF5umsk/maxresdefault.jpg)
Also included with every Renesis are proprietary mods which provide added cooling to the exhaust ports, helping to minimize side housing surface deformation at outer port edges as well as the area around leading spark plugs on the rotor housings.Īlso available with every Pettit Built Renesis is our service for the lower intake manifold. Prices are also subject to change and may increase or decrease depending on several factors that include availability of new Mazda parts, usable cores, and discounts from our purchase volumes.Įvery Pettit Built Renesis is blueprinted, street ported and receives all the modifications that make Pettit Built Engines the best. 13B Four Port Turbo Series 4 & 5 - $5850.Due to all the new parts, our standard 2 rotor build is $5895, plus a core charge of $800-$1000 and shipping were applicable. Pettit Built OTS engines typically include new rotor housings, rotors, gears, and e-shafts (unless otherwise listed on your quote). Pettit Engines are known for unsurpassed quality, top performance and outstanding reliability, all reasons why our rotary engines are considered to be the best by so many people all around the world. If you have no core, we can get a Pettit Built OTS Engine right to your door. Unless we purchase an engine for your build, we typically require no deposit or payments until your engine is scheduled to ship (or after your test drive, on car projects).
![rotary motor drag racing rotary motor drag racing](https://s1.cdn.autoevolution.com/images/news/gallery/mazda-rx-8-sets-rotary-1-4-mile-world-record-with-amazing-608s-pass_6.jpg)
Once approved, typical completion time is 8-10 working days, or 1-3 days for priority builds. The whole process takes 20-40 minutes, after which we document our findings and provide an accurate written quote for your approval. We encourage customers to participate on-site in the disassembly inspection and failure analysis of their engine. The old parts tell a story and reveal the causes of failure and/or problems that- once corrected- can help prevent a failure recurrence. We then call or email you with our findings and provide a written quote to build you the engine you desire. When your engine arrives, we disassemble it and perform wear pattern / failure analysis inspections. If the main core parts are all usable, our standard two rotor build can cost as little as $3200 for all the following engines:įor three rotor engines like the 20b or 13g, CALL US to discuss your project.
Rotary motor drag racing code#
Call or email us with your zip code for the terminal location nearest you. Or, you can drop it off at a freight terminal for a savings of $80- $125. To ship your engine, just give us a call at (561) 844-2258 and we can have it picked up. The easiest, best and most cost-effective way to get a Pettit Built Engine is using your old engine as the core.